If Your Turrent Is Off on the Paralex Adjustment Can You Reset to Read Right

Products:

• Kahles K16i 1-six×24
• Kahles K1050 10-50×56
• Kahles K312i 3-12×50
• Kahles K1050i FT 10-50×56
• Kahles K4i iv×xxx
• Kahles K624i 6-24×56
• Kahles K624i 6-24×56 MOAK
• Kahles K1050 10-50×56 MOAK
• Kahles K318i 3.v-eighteen×l
• Kahles K525i 5-25×56
• Kahles K18i one-8×24 SFP
• Kahles K525i 5-25×56 DLR

DEAR Client!

Congratulation and thank you for purchasing this professional competition Thousand product from KAHLES! Before using information technology for the starting time time, please read this
information carefully.

All specific technical data and reticle drawings of the KAHLES Thou products are available online at www.kahles.at.

If you lot have whatever further questions, please contact your authorized KAHLES dealer, gunsmith or contact our support squad directly.

Your KAHLES team

CONTENT

1 OPERATING ADJUSTMENTS

2 Apply AND MOUNTING

three SAFETY INSTRUCTIONS

four MECHANICAL CENTER

5 DIOPTER AND PARALLAX Aligning

six SIGHTING IN THE RIFLE Scope
half-dozen.1 Zeroing on K16i and K18i
6.2 Zeroing the height punch on K312i, K318i, K525i, K624i and K1050 MOAK
six.2a Zeroing the windage dial on K312i, K318i, K525i, K624i and K1050 MOAK
6.2b Reset to factory atmospheric condition (full elevation) on K312i, K318i, K525i, K624i and K1050 MOAK
half dozen.3 Zeroing the superlative dial on K1050/K1050i FT
half dozen.3a Zeroing the windage punch on K1050/K1050i FT

vii ELEVATION AND WINDAGE ADJUSTMENT

8 ROTATION INDICATOR Pivot

9 ANTI-ROTATION PROTECTION "TWIST GUARD"

10 ILLUMINATION

10.1 MAX LIGHT Function K18i

11 REPLACING THE BATTERY

12 STANDARD TOOL FOR K318i AND K525i

xiii MOUNTING OF K18i THROW LEVER

14 CLEANING

fifteen STORAGE

16 CONFORMITY

1 OPERATING ADJUSTMENTS

Kahles K Series Rifle Scopes Instruction Transmission

2 USE AND MOUNTING

KAHLES burglarize scopes are waterproof and extremely durable. All the same, conscientious handling is advised, specially around the turrets. Please protect your rifle scope against excessive touch and corruption.

To ensure proper function and performance employ a professional gunsmith to mount your KAHLES rifle telescopic. Ensure maximum eye relief is accomplished. Please read all rubber instructions before use.

3 Safety INSTRUCTIONS

• Never look direct into the sun or whatsoever other intense light through your rifle scope
• Please protect your rifle scope from excessive solar radiation and heat
• Please note the eye relief distance specified for properly mounting the rifle scope
• All repairs must exist performed by KAHLES
• The rifle scope must be mounted past professional gunsmith
• Attention – the screws of mounts shall in no case be tightened stronger than max. 240 Ncm / 21 in lbs
• Always check carefully and be certain that your firearm is unloaded before undertaking any piece of work upon it.

4 MECHANICAL CENTER

The reticle has been factory-ready to optical center. If you demand to reset it anyhow, follow these steps:
ane. Turn the elevation or windage adjustment until it stops (practice not force).
2. At present turn the aligning in the opposite direction while counting the total number of clicks until it stops.
iii. Half of this total number of clicks is the optical center.
iv. Echo this procedure for the 2nd adjustment turret.

Pay attention, never utilize whatever strong force when you lot do any adjustments on the turrets.

v DIOPTER AND PARALLAX Adjustment

• Turn the diopter compensation band (1) until you go a sharp reticle prototype
• Plough the parallax adjustment wheel (3) until you accomplish a sharp epitome and the reticle does not move on the target due to head placement.
• Magnification ring (2) turn to increase or decrease magnification

Kahles Grand Serial Rifle Scopes Instruction Manual

6 SIGHTING IN THE Burglarize Scope

Subsequently the burglarize scope has been properly mounted and bore sighted past a professional gunsmith you will need to sight in your burglarize and rifle scope. Attention – the screws of mounts shall in no case be tightened stronger than max. 240 Ncm / 21 in lbs!

Sight in the burglarize scope (on the shooting range) to your specific altitude and desired point of impact by turning the tiptop and windage adjustments to move the bullet bear on to your desired indicate of affect. The direction of bullet bear on is engraved on each adjustment. Once y'all have established the preferred point of impact on the target you will need to zero the elevation and windage adjustments. An pointer with "Up" at the superlative turret and an arrow with "R" on the side aligning turret mark the direction of rotation for a meeting point shift up ("Up") or rightwards ("R"). Expert mounting is required to ensure optimum performance.

6.1 Zeroing on K16i and K18i

Once y'all have aligned the scope to the rifle, you tin can retain this bones setting. The calibration for this is located on the index disc of the top/windage adjustment turret.

1. Hold the turret with your fingers

2. Utilise a coin or an empty cartridge case and turn the locking screw (one) in counter clockwise direction

iii. Loosen the locking screw till you lot get a gratuitous moving index disc (3)

four. Plow the index disc/ring (3) until the aught signal of the scale is aligned with the alphabetize point on the scope

five. Hold the index disc/ring (iii) and the turret disc (2) turn the locking screw clock wise in right direction. While performing this process you should hear no mechanical click.

6. Your aligning is at present zeroed to your point of impact.

Kahles K Series Rifle Scopes Instruction Manual

Pay attention, never use whatever stiff strength when y'all do whatsoever adjustments on the turrets.

6.2 Zeroing the elevation dial on K312i, K318i, K525i, K624i and K1050 MOAK

Using the supplied allen cardinal, loosen the two set screws on the turret 1– iii turns (do not remove the set screws completely) until you lot accept a free moving turret without clicks. With the set screws loosened plow the meridian turret in the downward direction (the direction of bullet impact is engraved on the aligning) until it stops. This volition be iii or 4 marks beneath the naught mark on the dial. Plow the turret so that the nix on the dial lines up with the indicator marking on the body tube. Marshal the marks and using the brusque end of the supplied allen key tighten once more the two set screws to approximately 1 Nm or 8 inch pounds. Your elevation is now zeroed.

The zero terminate is sited 3 or four clicks beneath the Zip indicator. This feature facitilitates the user finding the Zero indicator quickly and intuitively even in poor light weather and adapting the turret to special weather such every bit for example very loftier temperatures or closer targets.

Kahles K Serial Rifle Scopes Instruction Manual

Pay attending, never utilize whatever strong strength when you practice any adjustments on the turrets.

6.2a Zeroing the windage dial on K312i, K318i, K525i, K624i and K1050 MOAK

With the rifle and scope sighted in to the desired point of touch loosen the 2 set screws on the windage aligning dial 1– 3 turns (practice not remove the set screws
completely) and move the dial to align the zippo mark to the indicator mark on the body tube.

Using the short end of the supplied allen cardinal, tight the two gear up screws to approximately 1 Nm or 8 inch pounds. Your windage is now zeroed.

Kahles Chiliad Series Burglarize Scopes Teaching Manual

Pay attention, never utilize any strong force when yous do whatever adjustments on the turrets.

half dozen.2b Reset to manufactory conditions (total summit of the vertical adjustment) on K312i, K318i, K525i, K624i and K1050 MOAK

i. Turn the elevation turret (v) in the up direction until you reach the mechanical cease.

ii. Utilise the supplied allen key to loosen the two set screws i– three turns (exercise not remove the set screws completely) until you have a gratuitous moving turret without clicks.

3. Now turn the elevation turret in the upward direction until you lot accomplish the mechanical stop.

iv. Use the short end of the supplied allen key to tighten the ii gear up screws to approximately 1 Nm or 8 inch pounds.

v. Plow the tiptop turret in the down direction until you reach the mechanical terminate.

vi. Use the supplied allen primal to loosen the two set up screws 1– 3 turns (practice not remove the set screws completely) until you have a free moving turret without clicks.

7. At present plough the elevation turret in the down management until you reach the mechanical stop.

eight. Use the short end of the supplied allen key to tighten the two set screws to approximately 1 Nm or 8 inch pounds.

9. You have now deactivated the zero stop feature. Your rifle telescopic will now take full adjustment travel.

Note: The mechanical (concrete) finish will be about 3 or 4 clicks below nix. This allows adjustments slightly below cypher for special weather as increased temperature or closer targets.

Pay attending, never utilize any potent force when y'all do any adjustments on the turrets.

half-dozen.3 Zeroing the elevation dial on K1050/K1050i FT

Using the supplied allen cardinal loosen the 2 prepare screws on the turret ane– iii turns (practise not remove the set screws completely) until you have a free moving turret without any clicks. With the gear up screws loosened turn the pinnacle turret in the downward direction (the direction of bullet bear on is engraved on the aligning) then that the zero on the punch lines up with the indicator mark on the body tube. Align the marks and utilize the short terminate of the supplied allen primal to tighten the two set screws to approximately 1 Nm or 8 inch pounds. Your elevation is now zeroed.

Kahles G Series Rifle Scopes Pedagogy Manual

Pay attention, never use whatsoever stiff strength when you lot do any adjustments on the turrets.

6.3a Zeroing the windage dial on K1050/K1050i FT

With the rifle and telescopic sighted in to the desired signal of impact loosen the ii set screws on the windage aligning dial ane– 3 turns (do not remove the set screws completely) and move the punch to align the zero mark to the indicator mark on the torso tube. Using the short terminate of the supplied allen key, tighten the 2 set up screws to approximately i Nm or 8 inch pounds. Your windage is now zeroed.

Kahles One thousand Series Burglarize Scopes Educational activity Transmission

Pay attention, never use any strong force when you lot do any adjustments on the turrets.

vii Pinnacle AND WINDAGE Aligning

KAHLES riflescopes have adjustable height and windage dials with mechanical and audible clicks. On the K4i this is merely possible with a coin or cartridge example. Each click moves the point of bear upon towards the direction which is engraved on the turrets.

Pay attention, never employ whatever strong forcefulness when y'all exercise any adjustments on the turrets.

8 ROTATION INDICATOR PIN

Double turn turret

There are 2 rows of numbers (10) on the elevation aligning. If the indicator pin (seven) is flush to the top of the aligning you lot are using the lesser row of numbers (first rotation). If the indicator pin is raised upwards, you are using the upper row of numbers (second rotation).

At the K318i the pin's lifting is shown graphically past a raising post.

Kahles Yard Series Rifle Scopes Instruction Manual

Triple plow turret

At that place are 3 rows of numbers (Ten) on the meridian aligning. If the indicator pivot (vii) is flush to the summit of the adjustment you are using the bottom row of numbers (showtime rotation). If the indicator pivot is raised up well-nigh 1 mm (red), you are using the middle row of numbers (second rotation). If the indicator pin is raised up about 2 mm off the housing (white and red), the highest row of numbers (third rotation) is in employ.

Kahles K Series Burglarize Scopes Instruction Manual

9 ANTI-ROTATION PROTECTION "TWIST Guard"

The K318i and the K525i offering you the innovative and patented antitwist device "Twist Guard" on the windage turret. A free rotating disc protects the windage from unintended twisting.

Kahles 1000 Series Rifle Scopes Education Manual

10 ILLUMINATION

About KAHLES rifle scopes are equipped with illuminated reticles. To switch on the reticle illumination turn the illumination switch towards clockwise management. The illumination intensity will go brighter or lower by turning the adjustment switch more than or less. The adjustment can be turned in direction to the off point or to the desired intensity setting. The illumination is switched off when the indicator on the illumination adjustment is aligned with the off marking on the tube. All of our Grand-models have the automatic-off function of the reticle illumination integrated. If at that place volition exist no effulgence adjustment over a catamenia of about 2 hours, the reticle illumination automatically switches off. To restart the reticle illumination after the automatic-off is activated, you accept to switch it completely off and on again. In any case to prevent depletion of the bombardment, turn off the reticle illumination when not in use.

Kahles K Series Rifle Scopes Instruction Manual

10.1 MAX Lite Function K18i

The reticle illumination of the K18i is offering an boosted "MAX LIGHT Function", to guaranty the needed illumination intensity even at worse backlight situations. The brighter reticle illumination in the "MAX Light Role" is accomplished due to higher battery voltage and will reduce the lifetime of the bombardment.

Kahles K Serial Rifle Scopes Instruction Transmission

11 REPLACING THE BATTERY

The battery is stored in the illumination aligning.

To change the battery:

1. Turn off the reticle illumi – nation

2. Screw the battery comprehend (Depending on the model past mitt or with a coin) counter clockwise until the cover is unscrewed.

three. Change the bombardment (CR2032) positive + side facing out

four. Reinstall the bombardment cover securely

Kahles Thou Series Rifle Scopes Instruction Manual

Attention! Use simply type CR 2032 batteries. The K16i and K18i contains a spare battery inside the windage turret cap.

Disposal of used batteries

Batteries must not be tending of every bit household waste and you are legally obliged to render used batteries. Local facilities exist for returning used batteries free of charge (e.chiliad. in retail outlets or at communal collection points). Batteries are labelled with a crossed-out wheeled bin and the chemical symbol of the harmful substance they contain: "Cd" for cadmium, "Hg" for mercury and "Pb" for lead. Please help us to protect the environs.

12 STANDARD TOOL FOR K318i AND K525i

An Allen-key is stored in the cap of the K318i and K525i illumination unit of measurement. It can be used to spiral and unscrew the turret'south screws.

Kahles G Series Rifle Scopes Instruction Manual

13 MOUNTING OF K18i THROW LEVER

The K18i includes two different throw levers. These can exist easily changed and also the position of throw levers could be changed stepless, due to the individual needs. Therefore just open the screw with the torx wrench till the throw lever can easily be pulled off. Then the other throw lever have to be pulled on and fixed with the screw at the position which is needed. The spiral should just exist tightend hand-screwed.

Kahles One thousand Series Rifle Scopes Instruction Transmission

14 CLEANING

Nosotros take designed all elements and surfaces to require very little care.

KAHLES lens coatings makes cleaning objective lenses and eyepiece lenses easy, specially when cleaning dried-on mineral deposits (e.g. water marks from condensation). To ensure the long-lasting optical quality of your rifle scope, you should keep the glass surfaces free from clay, oil and grease. When cleaning the lenses, kickoff remove larger particles with an optical lens brush. For subsequent thorough cleaning, breathe lightly on the lens and clean with the cleaning textile. The metallic parts are best cleaned with a soft, lenscleaning cloth.

Standard Accessory

The special KAHLES Lens-Cleaning fabric can be used to clean even the most sensitive glass surfaces. It is suitable for the objective and eyepiece lens. Delight keep the microfiber cloth clean every bit dirt particles can damage the lens surface. If the cloth is dingy, it may be done in lukewarm soapy water and immune to dry out naturally. Please apply information technology exclusively for cleaning lens surfaces.

xv STORAGE

Nosotros recommend to store the rifle scope in a dry identify without excessive solar radiation and estrus. If the rifle scope is moisture it must be stale prior to storage.

16 CONFORMITY

The devices comply with Eu directives 2011/65/EU, 2012/19/EU und 2014/30/EU.

kingallogrishme.blogspot.com

Source: https://www.optics-trade.eu/blog/kahles-k-series-rifle-scopes-instruction-manual/

Share this post